Sunscreen is essential for protecting your skin, but it can leave unsightly greasy, white, or dark stains on concrete patios, driveways, and pool decks. These stains happen when the oils and chemical filters in sunscreen soak into the porous surface of the concrete. The good news is that you can usually remove them with common household supplies and a little elbow grease. Before you start, check the weather forecast—you will need a dry day with a few hours of sunshine, as most methods require the concrete to be dry and then rinsed thoroughly.
What You’ll Need
- Dish soap (a grease-cutting type works best)
- Baking soda
- White vinegar
- A stiff-bristled brush (a deck brush or old scrub brush)
- A bucket of warm water
- Hydrogen peroxide (for stubborn, dark stains)
- Cat litter, cornstarch, or baking soda (for fresh oil stains)
- A spray bottle
- Old rags or paper towels
- Plastic wrap (optional, for keeping a poultice moist)
Step-by-Step
- Blot up fresh sunscreen immediately. If the sunscreen has just spilled, use paper towels or an old rag to blot—do not rub, as that pushes the oil deeper into the concrete. Press down firmly to soak up as much as possible.
- Cover a fresh oil stain with an absorbent powder. Sprinkle a thick layer of cat litter, cornstarch, or baking soda over the wet sunscreen. Let it sit for several hours or overnight. The powder will draw the oil out of the concrete. Sweep it up and dispose of it in the trash.
- Mix a soapy cleaning solution. In a bucket, add a few squirts of dish soap to warm water. Stir gently. Dish soap is designed to break down oils, making it your first line of defense against sunscreen residue.
- Scrub the stain with the soapy water. Dip your stiff-bristled brush into the bucket and scrub the stained area in a circular motion. Work the suds into the concrete for a couple of minutes. The mechanical action of the brush is crucial for lifting the oil from the pores.
- Rinse with clean water. Pour a bucket of clean water over the area, or use a garden hose. This flushes away the soap, oil, and sunscreen residue. Inspect the area. If the stain is gone, let it dry completely.
- For remaining stains, make a baking soda paste. In a small bowl, mix baking soda with a little water to form a thick paste, about the consistency of toothpaste. Spread the paste over the entire stain in a layer about a quarter-inch thick.
- Let the paste sit and re-scrub. Leave the baking soda paste on the stain for at least half an hour. Then, using your brush, scrub the paste into the concrete. Rinse thoroughly and check the stain again.
- Use vinegar for stubborn white marks. If the stain is a white or chalky residue from mineral sunscreen, fill a spray bottle with white vinegar. Spray the stain generously and let it fizz for a few minutes. Scrub with your brush, then rinse with water.
- Try hydrogen peroxide for dark, set-in stains. For older or dark oil stains that resist the above steps, pour a small amount of hydrogen peroxide directly onto the stain. Let it bubble and sit for about ten minutes, then scrub and rinse. Test this on a small, hidden area of concrete first, as it can lighten the surface.
- Make a poultice for deeply embedded stains. If the stain persists, mix a thick paste of baking soda and water (or cat litter and water). Spread it over the stain, cover with plastic wrap to keep it moist, and leave it for a full day. The poultice will slowly draw the oil out. Remove the plastic wrap, let it dry, then brush it away and rinse.
- Rinse and dry completely. After any treatment, give the area a final, thorough rinse with clean water. Let the concrete dry for a full day. Sunscreen stains often fade significantly as the concrete dries, so do not judge the result while it is still wet.
Common Mistakes
- Rubbing a fresh spill. Wiping or rubbing a fresh sunscreen spill only spreads the oil and pushes it deeper into the concrete pores. Always blot.
- Using a pressure washer too early. A pressure washer can blast the oil deeper into the concrete or etch the surface. It is better to try gentler chemical and scrubbing methods first.
- Skipping the drying time. Concrete looks darker when wet, so a stain may seem worse than it is. Many stains disappear once the concrete is fully dry. Rinsing and then immediately re-treating a stain that is already gone is wasted effort.
- Using bleach on colored concrete. Bleach can lighten or discolor tinted or stamped concrete. Stick to dish soap, baking soda, and vinegar for most stains.
- Letting the stain sit for weeks. The longer sunscreen sits, the deeper it penetrates. Treat spills as soon as you notice them for the best chance of full removal.
Tips
- Test any cleaner on a hidden spot first. Before applying vinegar, hydrogen peroxide, or a poultice to a visible area, test it on a small, inconspicuous corner of the concrete to ensure it does not cause discoloration.
- Use a dedicated brush. Keep a stiff-bristled brush just for outdoor cleaning. A brush with synthetic bristles is more durable on rough concrete than a natural-bristle brush.
- Work on a warm, dry day. Sunlight and warmth help the cleaning agents work and speed up the drying process. Avoid treating stains right before rain.
- Seal your concrete. After the stain is removed and the concrete is completely dry, consider applying a concrete sealer. A sealed surface is far less porous and will make future sunscreen spills much easier to wipe away.
- Reapply the poultice if needed. A single poultice application may not pull out all the oil from a deep stain. You can repeat the process with fresh paste for several days until the stain fades.
Troubleshooting
- The stain is still visible after the dish soap scrub. This is normal for older stains. Move directly to the baking soda paste or the poultice method. Patience is key—you may need to repeat the poultice treatment a few times.
- The white residue will not come off with vinegar. Some mineral sunscreens leave a stubborn zinc oxide or titanium dioxide film. Try a paste of baking soda and water, scrub gently, and rinse. If that fails, the residue may have etched the concrete surface, leaving a permanent light mark. In that case, a concrete cleaner designed for oil stains may help, but you may need to accept a faint shadow.
- The stain reappears after drying. This means oil is still wicking up from deeper in the concrete. Apply a fresh poultice and leave it on longer—up to two days—to draw out more oil. You may also need to repeat the entire cleaning process a second time.
- Hydrogen peroxide lightened the concrete. If you notice a lighter patch, rinse the area thoroughly with water. The lightening is often temporary and may fade as the concrete rehydrates. If it is permanent, you may need to blend it by scrubbing the surrounding area with a mild cleaner, or accept the slight color difference.
- The stain is on a vertical surface. Poultices and pastes will slide off a wall or step riser. Instead, soak a thick rag in the cleaning solution, press it against the stain, and hold it in place with tape or a weight for several hours. Then scrub and rinse.
Frequently Asked Questions
Will sunscreen permanently stain concrete?
Not always. Fresh stains are usually removable with prompt cleaning. However, if sunscreen sits for weeks or months, the oils can penetrate deeply and leave a permanent dark mark. Sealing your concrete helps prevent this.
Can I use a pressure washer to remove the stain?
Yes, but only after you have tried chemical and scrubbing methods. A pressure washer can remove surface residue, but it can also drive oil deeper into the pores or damage the concrete surface. Use a wide spray pattern and keep the nozzle moving.
Is it safe to use bleach on concrete for sunscreen stains?
Bleach is not recommended for sunscreen stains because it does not break down oils well, and it can discolor colored or stamped concrete. Dish soap, baking soda, and hydrogen peroxide are safer and more effective options.
Why does my sunscreen leave a white film on concrete?
That white film is usually from mineral sunscreens containing zinc oxide or titanium dioxide. These ingredients are not oils, so they need a different approach. Vinegar helps dissolve the mineral residue, followed by a good scrub with soapy water.
How long should I leave a baking soda poultice on the stain?
For best results, leave the poultice on for at least a full day, and up to two days for stubborn stains. Keep it covered with plastic wrap so it does not dry out too quickly. The longer it stays moist, the more oil it can draw out.
Can I use dish soap alone to remove an old stain?
Dish soap is great for fresh spills, but it is usually not strong enough for set-in stains. Combine it with scrubbing, and then follow up with a baking soda paste or poultice for older, deeper stains.