If your air conditioner has stopped cooling, tripped a breaker, or simply won’t turn on, the reset button is often the first thing to check. This small button can restore power to the compressor and get your system running again without a service call. Before you start, make sure the unit is unplugged or the breaker is off to avoid any electrical hazard. You’ll also want a flashlight and possibly a screwdriver to access the button.
What You’ll Need
- Flashlight
- Flathead screwdriver (for prying open panels or access doors)
- Gloves (optional, for protection)
Step-by-Step
- Turn off the power. Go to your electrical panel and switch off the breaker that feeds the AC unit. If you have a disconnect box near the outdoor unit, pull the handle to cut power. This is critical for your safety.
- Locate the outdoor unit. The condensing unit sits outside your home, usually on a concrete pad. It has a large fan on top and metal grilles on the sides.
- Remove the access panel. Look for a small panel on the side of the unit, often held by one or two screws. Use a screwdriver to remove them and pull the panel off. Set the screws aside in a safe place.
- Find the reset button. Inside, near the compressor (the cylindrical black or silver component), you’ll see a small red or yellow button. It may be labeled “RESET” or have a red cap. This is the overload reset switch. On some units, it’s located behind a small rubber plug on the side of the compressor.
- Press the button. Press it firmly until you feel a click. If it doesn’t click, it may already be reset. Do not hold it for more than a few seconds.
- Replace the panel. Put the access panel back on and secure it with the screws.
- Restore power. Turn the breaker back on or reinsert the disconnect. Wait a few minutes, then set your thermostat to cool and check if the system starts.
Common Mistakes
- Forgetting to turn off power. Never open the unit while it’s live. Even if the thermostat is off, the compressor can still have power.
- Pressing the wrong button. Some units have a test button on the circuit board or a small reset on the fan motor. The reset you want is on or near the compressor.
- Holding the button too long. A quick press is all it takes. Holding it can damage the switch.
- Ignoring the thermostat. If the thermostat is set to “off” or the batteries are dead, the AC won’t start even after a reset.
- Not checking the air filter. A clogged filter can cause the system to overheat and trip the reset again. Always check the filter before resetting.
Tips
- Know your unit. Some models have the reset button behind a small access door on the side, not under a full panel. Check your owner’s manual for the exact location.
- Listen for a click. When you press the button, you should hear a distinct click. If not, it might already be tripped or the switch is faulty.
- Wait after resetting. Give the system a few minutes to restart. The compressor has a built-in delay to prevent short cycling.
- Clean the area. Debris around the outdoor unit can cause overheating. Keep plants and clutter at least a couple of feet away.
- Use a flashlight. The inside of the unit is dark, and the button can be small. A flashlight helps you see it clearly.
Troubleshooting
- No click when pressing. If the button doesn’t click, it may already be reset. Try turning the power back on and see if the unit runs. If not, the switch might be defective and need replacement.
- Unit still won’t start. Check the thermostat settings, replace batteries if needed, and ensure the breaker hasn’t tripped again. Also check the air filter and replace if dirty.
- Reset trips again immediately. This indicates a deeper problem, such as a faulty capacitor, a failing compressor, or a refrigerant leak. Do not keep resetting; call a professional HVAC technician.
- Button is stuck. If the button is jammed, do not force it. Gently wiggle it with a small screwdriver. If it breaks, you’ll need a replacement switch.
- No reset button at all. Some modern units don’t have a manual reset; they reset automatically after the power is interrupted. Simply turn the breaker off for a few minutes, then back on.
Frequently Asked Questions
- Why does my AC keep tripping the reset? The most common cause is overheating due to a dirty condenser coil, a failing fan motor, or a faulty capacitor. It can also happen if the compressor is drawing too much current.
- Can I reset my AC from the thermostat? No, the reset button is only on the outdoor unit or, in some cases, on the indoor air handler. The thermostat only controls temperature and fan settings.
- How often should I press the reset button? You shouldn’t need to press it regularly. If you find yourself resetting frequently, there’s an underlying issue that needs professional attention.
- Is it safe to press the reset button myself? Yes, as long as you turn off power first and follow the steps. It’s a simple mechanical switch, not a complex electrical component.
- What if there’s no reset button on my unit? Many newer units don’t have a manual reset; they reset automatically when power is restored. Try turning the breaker off for a few minutes, then back on.
- Can a dirty air filter cause the reset to trip? Yes, a clogged filter restricts airflow, causing the system to overheat. This can trip the safety reset. Change your filter regularly to avoid this.
Where Is the Reset Button on My AC Unit?