Knowing the names of door parts is useful for shopping for replacements, following repair guides, or just talking to a contractor. This guide walks through the standard parts of an interior or exterior hinged door, from the frame to the hardware, and explains what each piece does.
What You’ll Need
- No special tools—just a door you can look at (open and closed).
- Optionally, a flashlight to see the hinges and weatherstripping clearly.
Step-by-Step
- Start with the frame (the fixed part). The entire wood or metal surround that the door fits into is the door frame. It has three main pieces: the head (the top horizontal piece), the jamb (the two vertical side pieces), and the sill (the bottom piece, usually only on exterior doors). The vertical jambs are often called the hinge jamb (where hinges attach) and the strike jamb (where the latch goes).
- Look at the trim around the frame. The decorative molding that covers the gap between the frame and the wall is called casing (or trim). On the floor, the piece that covers the gap between the floor and the door is the threshold—this is the raised strip you step over on exterior doors.
- Examine the door slab (the moving part). The large flat panel that swings is the door slab or simply the door. Its main surfaces are the face (front and back) and the edges. The vertical edges are the stiles (the hinge stile and the lock stile), and the horizontal edges are the rails (top rail, bottom rail, and sometimes a middle rail).
- Check the panels and glass. If your door has recessed or raised sections, those are called panels. If it has glass, the glass panes are called lites (or lights), and the small strips that hold the glass in place are muntins (or grilles).
- Inspect the hinges. The metal hardware that attaches the door to the frame consists of hinges. Each hinge has two leaves (flat plates) connected by a pin. The leaf on the door is the door leaf, and the one on the frame is the jamb leaf.
- Identify the locking and latching hardware. On the lock stile, you’ll see the latch (the spring-loaded bolt that keeps the door closed) and the latch bolt (the metal piece that slides into the strike plate). The strike plate is the metal plate on the frame that the latch catches. The deadbolt is a separate, heavier bolt that is turned with a key or thumb turn. The door handle (or knob) is what you grip, and the lockset is the entire assembly of handle, latch, and deadbolt.
- Look for weatherstripping and seals. On exterior doors, you’ll see a rubber or foam strip around the frame called weatherstripping—it seals gaps to keep out air and water. At the bottom, a door sweep (a rubber flap) attaches to the bottom of the door to seal the gap under it.
- Note the door stop. This is a thin piece of wood or metal attached to the frame that the door closes against. It prevents the door from swinging too far.
- Consider additional parts. Some doors have a peephole (a small viewer), a door closer (the hydraulic arm that pulls the door shut), or hinge pins that can be removed. On sliding doors, the parts are different—the track and rollers replace hinges.
Common Mistakes
- Calling the entire frame the “doorjamb.” The jamb is just the vertical side pieces; the top is the head.
- Confusing the latch with the deadbolt. The latch is spring-loaded and retracts when you turn the knob; the deadbolt is manually thrown with a key or thumb turn.
- Using “trim” for every piece. Trim usually refers to the casing around the frame, not the weatherstripping or the door stop.
- Thinking the threshold is the same as the sill. The sill is the bottom of the frame; the threshold is the raised strip on top of the sill that you step over.
Tips
- When ordering a replacement door, measure the slab size (width and height) and note whether it’s left-handed or right-handed (stand facing the door; if the hinges are on your left, it’s left-handed).
- Take a photo of the existing hardware before removing it so you know what to buy.
- For a quick reference, sketch the door and label each part as you identify it.
Troubleshooting
- If you can’t find the strike plate: It’s on the frame, not the door. Look for the metal plate with a hole that the latch slides into.
- If your door has no visible hinges (like a pocket door): It uses a track and rollers hidden in the wall, so the parts are different—look for the track on the floor or ceiling.
- If the door has no weatherstripping: That’s common on interior doors; only exterior doors typically have it.
- If the door has a glass insert but no muntins: Some doors use a single pane of glass with a decorative grid applied on top—that grid is still called muntins, but it’s not structural.
Frequently Asked Questions
Q: What is the difference between a door jamb and a door frame?
A: The frame is the entire structural surround (head, jambs, and sill). The jambs are specifically the two vertical side pieces.
Q: What is the piece at the bottom of the door that touches the floor?
A: That’s the door bottom or the door sweep (if it’s a rubber flap). The threshold is on the floor, not on the door.
Q: What is the metal plate on the door frame that the latch goes into?
A: That’s the strike plate.
Q: What are the horizontal and vertical parts of a door called?
A: The vertical edges are stiles, and the horizontal edges are rails. The top rail, bottom rail, and side stiles form the outer frame of the door slab.
Q: What is the trim around a door called?
A: The decorative molding around the frame is called casing or trim. The piece at the floor is the threshold (exterior) or a transition strip (interior).
Q: What is a door stop?
A: It’s a thin strip on the frame that the door closes against, preventing it from swinging too far. It’s often part of the frame, not a separate piece.