Quick Release Knot: Easy Step-by-Step Guide

A quick release knot, also known as a slipped knot or a draw loop knot, is a way to secure a rope or cord that can be undone with a single, firm pull on the loose end. It is useful for temporary ties, such as tethering a boat to a cleat, hanging a hammock, securing a tarp, or tying a bundle that you will need to free quickly. The key is that the final loop is a “slip” loop, so the whole knot collapses when you tug the working end. No special tools are needed, just a length of flexible rope or cord.

What You’ll Need

  • A length of rope or cord (any flexible type works, from paracord to clothesline)
  • An object to tie around, such as a post, ring, or handle (optional, but helpful for practice)

Step-by-Step

This method creates a reliable quick release knot around a post or ring. Practice with a loose rope first to get the motion down.

  1. Form a loop: Take the working end (the part you are holding) and cross it over the standing part (the long, fixed part of the rope) to form a simple loop. You should have a crossing point where the two parts meet.
  2. Bring the working end behind: Pass the working end behind the standing part, then bring it up through the loop you just formed. This is the start of a standard overhand knot.
  3. Do not tighten yet: Leave this first knot loose. You need room to work the next step. You should now have a loose overhand knot sitting on the rope.
  4. Create a bight: Take the working end and fold it back on itself to create a U-shaped bend, called a bight. The bight should be a few inches long, depending on how much rope you want to pull later.
  5. Insert the bight: Push this bight through the loose overhand knot, following the same path the working end took. The bight should emerge from the knot on the same side where the working end came out.
  6. Tighten the knot: Hold the bight in place with one hand, and pull firmly on the standing part with the other hand. This cinches the knot down around the bight. Make sure the knot is snug but not so tight that you cannot pull the bight out.
  7. Test the release: To release, simply pull the loose working end that sticks out of the knot. The bight will slip back through, and the entire knot will fall apart instantly.

If you are tying around a post, do the same steps but wrap the rope around the post first, then follow the steps with the two ends in front of you.

Common Mistakes

  • Pulling the wrong end: The most common error is pulling the standing part instead of the working end. Only the working end (the short tail) will release the knot. Pulling the standing part will just tighten it further.
  • Tightening before inserting the bight: If you cinch the first overhand knot down before you push the bight through, you will not be able to get the bight in. Keep it loose until the bight is in place.
  • Bight too short: If the bight is very short, it can slip out on its own under load, or be hard to grab when you want to release. Make the bight at least a couple of inches long.
  • Bight twisted: If the bight is twisted when you push it through, the knot may jam and not release cleanly. Keep the bight flat and untwisted.
  • Not testing before trusting: Using a quick release knot for something critical without first testing the release motion is risky. Always give the working end a tug before relying on it.

Tips

  • Use a contrasting color: If your rope has a colored core or a whipping, mark the working end with tape or a marker. This makes it obvious which end to pull, especially in low light.
  • Practice one-handed: Once you are comfortable, practice tying and releasing with one hand. This is a valuable skill if you are holding something with the other hand.
  • Adjustable tension: You can use this knot to create an adjustable loop. Tie the quick release around the standing part of the same rope, then slide the knot up or down to change the loop size before tightening.
  • For heavy loads: For very heavy loads, consider adding a half hitch after the quick release knot for extra security, but remember you will need to undo the half hitch first to release.
  • Keep it dry: Wet or icy rope can make the knot slip or jam. If the rope is wet, test the release a few times to make sure it still works.

Troubleshooting

  • The knot jams and won’t release: This usually means the bight was twisted or the knot was pulled extremely tight. Try wiggling the working end while pulling. If it still jams, you may need to work the knot loose with your fingers, which defeats the purpose. To prevent this, ensure the bight is flat and not twisted, and do not overtighten.
  • The knot comes undone on its own: If the bight slips out without you pulling it, the knot is not tight enough, or the bight is too short. Retie it, making the bight longer and pulling the standing part harder to cinch it down.
  • The working end is too short to pull: You need a tail of at least a few inches beyond the knot. If it is too short, you cannot get a grip. Retie with a longer working end.
  • The rope is too stiff: Very stiff or thick rope can be hard to work with. Moisten it slightly or use a more flexible cord. If you must use stiff rope, make the bight larger to give yourself more leverage.
  • You tied it around the wrong object: If you tied the knot around the object itself, rather than around the rope, it will not release. The bight must be part of the rope, not around the post. Untie and retie correctly.

Frequently Asked Questions

Is a quick release knot the same as a slip knot?
Yes, in common usage they are the same thing. A slip knot is any knot that uses a bight to create a loop that can be undone by pulling the working end. The quick release knot is a specific type of slip knot.

Can I use this knot for climbing or safety lines?
No. This knot is not suitable for life-safety applications. It can slip under load or when bumped. For climbing, use a figure-eight follow-through or other certified climbing knots.

What is the best rope for this knot?
Any flexible, non-slippery rope works well. Paracord, cotton clothesline, and natural fiber ropes hold the knot well. Very slick synthetic ropes like some polypropylene may slip more easily.

How do I tie it around a post if I can’t get to the end?
If you have a long rope and cannot pass the end around, you can tie a quick release on a bight. Form a bight in the middle of the rope, tie the quick release knot using that bight as the working end, and then slip the loop over the post. Pulling the loose end of the bight will release it.

Why does my knot keep tightening instead of releasing?
You are likely pulling the standing part (the long, load-bearing end) instead of the working end. Check which end you have in your hand. The working end is the short tail that sticks out from the knot.

Can I make the loop bigger or smaller after tying?
Yes, if you tie the quick release knot around the standing part of the same rope (not around a post), you can slide the knot up or down to adjust the loop size before you tighten it fully. Once tightened, it holds its size until released.

Quick Release Knot: Easy Step-by-Step Guide

Leave a Reply

Your email address will not be published. Required fields are marked *

Scroll to top