Soaking dried beans before cooking shortens their simmering time and helps them cook more evenly. The quick soak method does in about an hour what an overnight soak does in several hours, making it a great option when you decide to make beans the same day. It also helps remove some of the complex sugars that can cause gas for some people. Here’s how to do it right.
What You’ll Need
- Dried beans (any variety, but note that older beans may take longer)
- A large pot or Dutch oven with a lid
- Water
- Salt (optional, for seasoning later)
- A colander for draining
Step-by-Step
- Pick over the beans. Spread the dried beans on a clean counter or a light-colored plate. Remove any small stones, debris, or beans that look shriveled or discolored. Rinse the beans thoroughly under cool running water in a colander.
- Place beans in a large pot. Use a pot that gives the beans plenty of room to expand—they will roughly double in size. A good rule is to use a pot that holds at least three times the volume of the dried beans.
- Add water. Cover the beans with cold water by about two inches. Use more water if needed; the beans should be fully submerged with extra room to spare.
- Bring to a rolling boil. Set the pot over high heat and bring the water to a full, vigorous boil. Let it boil for about two minutes.
- Remove from heat and cover. Turn off the burner, put the lid on the pot, and let the beans sit in the hot water for one hour. During this time, the beans will absorb water and soften slightly.
- Drain and rinse. After the hour is up, pour the beans into a colander and discard the soaking water. Rinse the beans with fresh water. This step is important—it washes away some of the sugars that can cause digestive discomfort.
- Cook as usual. Return the beans to the pot and add fresh water or broth, enough to cover them by about two inches. Bring to a simmer, then reduce the heat to low and cook gently until tender. Cooking time will vary by bean type and age; check often and add more liquid if needed. Salt the beans near the end of cooking, as salting early can sometimes make the skins tough.
Common Mistakes
- Skipping the boil. The quick soak relies on the initial boil to start the hydration process. If you just put the beans in hot water without boiling, they won’t soften as much in the hour.
- Using too little water. Beans expand significantly. If the water level is too low, some beans will stay above the water line and remain hard.
- Soaking for too long after boiling. Leaving the beans in the hot water for more than a couple of hours can cause them to ferment slightly, leading to an off flavor. Stick to the one-hour mark.
- Reusing the soaking water. The soaking water contains the sugars that cause gas. Always drain and rinse after soaking.
- Adding acid or salt too early. Acidic ingredients like tomatoes, vinegar, or wine, and salt, can slow down the softening of the bean skins. Add them after the beans are mostly tender.
Tips
- For even softer, more digestible beans, you can add a piece of kombu (a type of seaweed) to the cooking pot. It’s not necessary, but some cooks find it helps. Discard the kombu before serving.
- If you have time, a longer soak (overnight) will produce slightly plumper beans, but the quick soak works perfectly well for most recipes.
- Cook a big batch and freeze the extras in portion-sized containers. Quick-soaked beans freeze beautifully and are a great convenience.
- Different beans cook at different rates. Small beans like lentils or black-eyed peas may not need a soak at all, while larger beans like chickpeas or kidney beans benefit the most from this method.
- If you’re making a soup or stew, you can quick-soak the beans and then add them directly to the pot, just be sure to adjust the liquid and cooking time.
Troubleshooting
- Beans are still hard after cooking. This can happen if the beans are old (they lose moisture over time) or if the water was too acidic. Continue simmering, adding more hot water as needed, and test every few minutes. If they still won’t soften, they may be too old and will likely never become tender—it’s best to start over with a fresher batch.
- Beans split or turn to mush. This usually means they were cooked too vigorously or for too long. Next time, keep the heat at a gentle simmer and check them earlier. For salads, you can add a little salt to the cooking water to help them hold their shape.
- Beans have a metallic or off taste. This can happen if you soak them for too long or if the soaking water wasn’t discarded. Always drain and rinse well. Also, avoid cooking beans in an aluminum pot, which can react with the beans.
- Foaming during cooking. Some beans, especially chickpeas, produce foam. Skim it off with a spoon. It’s harmless but can make the pot boil over. You can also add a teaspoon of oil to the water to reduce foaming.
- Beans are too salty. If you salted too early and the beans are salty, you can drain some of the cooking liquid and replace it with fresh water, or add a peeled potato to the pot to absorb some salt (discard the potato before serving).
Frequently Asked Questions
- Can I quick-soak any type of bean? Yes, this method works for most dried beans, including black beans, pinto beans, kidney beans, and chickpeas. Small beans like lentils and split peas don’t need soaking at all.
- Do I need to boil the beans for exactly two minutes? No, the exact time isn’t critical. The goal is to bring the water to a full boil and let it boil for a couple of minutes to start the hydration. A minute or three is fine.
- Can I skip the soaking and just cook the beans longer? Yes, you can cook unsoaked beans, but they will take much longer and may cook unevenly. The quick soak reduces cooking time and helps ensure a consistent texture.
- Is it safe to leave the beans in the hot water for more than an hour? It’s not recommended to leave them for more than a couple of hours, as they can begin to ferment. If you need to soak longer, do an overnight soak in the refrigerator.
- Do I have to discard the soaking water? Yes, discarding the soaking water helps remove some of the complex sugars that cause gas. It also removes any impurities from the beans.
- Can I add baking soda to the soaking water to soften beans faster? Some people add a pinch of baking soda to the soaking water, but it can give the beans a slightly soapy taste and destroy some nutrients. It’s better to rely on the boiling and soaking method without it.
Quick Soaking Beans Method: Fast Way to Prep