Combining two loft beds into an L-shape is a smart way to maximize floor space in a shared kids’ room or a small apartment. The result gives each sleeper their own elevated nook while freeing up the area underneath for desks, storage, or a play zone. This guide covers the safe way to join two identical or similar loft beds at a right angle, using brackets and bolts. Before you start, confirm that both beds are the same height and that the manufacturer allows modifications (some warranties void if you drill extra holes). You’ll also need a second person for lifting and aligning.
What You’ll Need
- Two loft beds of matching height (same model is easiest)
- Heavy-duty L-shaped corner brackets (at least four)
- Bolts, nuts, and washers that fit the brackets and the bed frame holes
- Drill with metal or wood bits (depending on your frame material)
- Screwdriver or socket wrench
- Measuring tape
- Level
- Pencil or marker
- Safety glasses and work gloves
Step-by-Step
- Clear the area. Remove mattresses, bedding, and anything stored under or on the beds. You need a clean, open floor to work safely.
- Disassemble what’s needed. If your loft beds have side rails that would block the corner connection, remove them according to the manufacturer’s instructions. Keep all screws and parts labeled.
- Position the first bed. Place one loft bed against the wall where you want the long arm of the L. Make sure it’s level and stable. Use the adjustable feet or add shims if the floor is uneven.
- Position the second bed. Bring the second loft bed in at a right angle to the first, so the end of one bed meets the side of the other. The beds should touch at the corner. Adjust until the tops are exactly the same height.
- Check alignment. Use a level across the top rails of both beds at the corner. They must be flush and level. If one is higher, adjust the legs or add shims underneath.
- Mark the bracket locations. On the inside of the corner, decide where to place your L-brackets. You want at least two brackets on the vertical posts and two on the horizontal rails. Mark the screw holes with a pencil.
- Pre-drill holes. If your frame is metal, use a metal bit slightly smaller than your bolts. For wood, use a wood bit. Drill pilot holes at your marks. This prevents splitting and makes bolting easier.
- Attach the brackets. Hold an L-bracket against the two beds so it spans the joint. Insert bolts through the bracket and into the pilot holes. Add washers and nuts, then tighten with a wrench or screwdriver. Repeat for all brackets.
- Double-check stability. Once all brackets are tight, try to wiggle the beds. There should be no movement at the joint. If there is, tighten further or add more brackets.
- Reinstall any removed parts. Put back any rails or guardrails you took off, following the original instructions. Make sure all fasteners are secure.
- Test the weight. Before letting anyone sleep on the beds, press down firmly on the corner joint from above. Then have a helper do the same from below. If anything creaks or shifts, reinforce with additional brackets.
Common Mistakes
- Mismatched heights: If the beds aren’t exactly the same height, the L will be unstable and unsafe. Always measure and level before bolting.
- Skipping pilot holes: Drilling directly into metal or wood without a pilot hole can cause the material to crack or the screw to strip. Always pre-drill.
- Using undersized brackets: Small, flimsy brackets won’t hold the weight. Use heavy-duty L-brackets rated for the load.
- Over-tightening: Tightening bolts too much can strip the threads or crush the frame. Tighten until snug, then give a quarter turn more.
- Ignoring the manufacturer’s warnings: Some loft beds are not designed to be modified. Check the manual or contact the company first.
Tips
- Use thread-locking adhesive on the bolts to prevent them from loosening over time from movement.
- Place a thin rubber mat or furniture pad between the two beds at the joint to reduce squeaking.
- If the beds have different finishes, that’s fine—the L-shape will still look intentional.
- Consider adding a vertical support post at the outer corner of the L if the beds feel wobbly, especially for taller loft models.
- Take photos before disassembling so you remember how to put things back.
Troubleshooting
- The beds don’t align perfectly. Loosen all brackets, adjust the beds, and re-tighten. If the floor is uneven, use shims under the legs.
- The joint creaks or moves. Tighten all bolts. If the problem persists, add more brackets or a wooden brace across the inside corner.
- You can’t find brackets that fit. Look for universal L-brackets at a hardware store. You can also use right-angle plates meant for construction.
- The beds are different heights. You can add furniture risers under the shorter bed’s legs, but only if they are stable and rated for the weight. Never stack risers.
- You’re worried about the warranty. Check with the manufacturer before drilling. Some allow modifications, others don’t. If not, consider using heavy-duty zip ties or rope as a temporary solution, but that’s not a permanent safe fix.
Frequently Asked Questions
- Can I connect two different loft bed models? Yes, as long as the heights match and the frames are similar in thickness. Use adjustable brackets to bridge any small gaps.
- Do I need to bolt the beds to the wall as well? It’s highly recommended. Even with the L-shape, loft beds should be anchored to wall studs for safety, especially for kids. Follow the original bed’s instructions for wall anchoring.
- How much weight can the L-connection hold? It depends on the brackets and the bed frame. Use heavy-duty brackets rated for at least the weight of a sleeping adult. The connection is meant to stabilize, not to bear the full weight of the bed—that’s still the legs’ job.
- Will this work with bunk beds? Yes, you can use the same technique to connect two bunk beds in an L-shape, but make sure the heights align and you have enough vertical clearance for the upper bunks.
- Can I take them apart later? Yes, just remove the bolts and brackets. You may have leftover pilot holes, but those can be filled with wood filler or left as-is.
- Is it safe for toddlers? Loft beds are generally not recommended for children under six years old, regardless of how they’re arranged. Always use guardrails and follow age guidelines from the manufacturer.
How to Hook Loft Beds Together in an L Shape