Make Cool Season Grass Plugs: A Step-by-Step Guide

Cool season grass plugs are a practical way to fill bare patches, transition to a new turf type, or establish a lawn without reseeding the whole area. Plugs are small sections of living grass with roots, and when planted in a grid, they spread and fill in over time. This guide walks you through the process from preparation to aftercare, so you can get a healthy, dense lawn. Before you start, make sure you have the right grass type for your region (like fescue, ryegrass, or bluegrass) and that the soil is workable—not frozen or waterlogged.

What You’ll Need

  • Cool season grass plugs (purchased or cut from existing lawn)
  • Soil test kit (optional but recommended)
  • Compost or topsoil (if soil is poor)
  • Starter fertilizer (low nitrogen, higher phosphorus)
  • Garden trowel or plugger tool
  • Rake
  • Garden hose or sprinkler
  • String or measuring tape (for spacing)
  • Gloves (optional)

Step-by-Step

  1. Test and prepare the soil. Test your soil pH and nutrient levels if possible. Cool season grasses prefer a pH between 6.0 and 7.0. Adjust pH with lime (to raise) or sulfur (to lower) according to the test results. Spread a thin layer of compost or topsoil over the area and mix it into the top few inches with a rake.
  2. Fertilize lightly. Apply a starter fertilizer at the rate recommended on the bag. This encourages root growth. Avoid high-nitrogen fertilizers, which promote leaf growth over roots.
  3. Moisten the soil. Water the area lightly a day before planting. The soil should be damp but not muddy. This makes it easier to insert plugs and helps them establish.
  4. Lay out your grid. Decide on spacing. For faster fill, space plugs about 6 inches apart; for larger areas, you can space them up to a foot apart. Use string lines or a measuring tape to mark rows so your grid is even.
  5. Dig holes. Use a trowel or a plugger tool to dig holes slightly larger than the root ball of each plug. The depth should match the plug’s root length so the top of the plug sits level with the surrounding soil.
  6. Plant the plugs. Place each plug in a hole, firming the soil around it to eliminate air pockets. The top of the plug should be flush with the ground—not buried or sticking up. Water each plug as you go if the soil is dry.
  7. Water thoroughly. After planting, water the entire area deeply so the soil is moist to a depth of several inches. This helps the plugs settle and encourages root contact with the soil.
  8. Keep the soil moist. For the first couple of weeks, water daily or as needed to keep the top inch of soil consistently moist. Avoid letting it dry out completely. Once the plugs start showing new growth, gradually reduce watering frequency.
  9. Mow when ready. Once the plugs have grown to about a third higher than your desired mowing height, mow them with a sharp blade. Keep the mower set high to avoid stressing the young grass.
  10. Fertilize after establishment. About a month after planting, apply a balanced fertilizer (like a 10-10-10) at the recommended rate to encourage spreading. Follow local guidelines for fall fertilization of cool season grasses.

Common Mistakes

  • Planting too deep or too shallow. If the plug is buried, the crown may rot; if it’s too high, roots dry out. Keep the top level with the soil.
  • Letting the soil dry out. Plugs have limited root systems and dry out quickly. Consistent moisture is crucial in the first few weeks.
  • Planting in the wrong season. Cool season grasses should be plugged in early fall or early spring when temperatures are mild. Summer heat stresses new plugs.
  • Skipping soil preparation. Plugs need loose, fertile soil to root. Planting into compacted or weedy soil leads to failure.
  • Using too much fertilizer. Over-fertilizing can burn roots or cause excessive leaf growth at the expense of roots.

Tips

  • Choose a grass variety suited to your sun and shade conditions. Fescues tolerate shade; ryegrasses prefer sun.
  • If you’re cutting plugs from an existing lawn, water it a day before to make cutting easier and reduce shock.
  • Plant in the late afternoon or on a cloudy day to reduce stress from heat and sun.
  • Use a plugger tool that removes a core of soil; this makes holes uniform and speeds up planting.
  • Consider mixing a little compost into the backfill soil for each hole to give plugs a nutrient boost.
  • Keep foot traffic off the plugged area until the grass is established.

Troubleshooting

  • Plugs are wilting or turning brown. This usually means they’re not getting enough water. Check the soil moisture—if it’s dry, water immediately and increase watering frequency. If the soil is waterlogged, reduce watering and improve drainage.
  • Plugs are not spreading. This can happen if the soil is nutrient-poor or too compacted. Aerate the area and apply a balanced fertilizer. Also, ensure the grass type is actually a spreading variety (some fescues are bunch-type and spread slowly).
  • Weeds are invading. Hand-pull weeds regularly until the grass fills in. Avoid using pre-emergent herbicides, as they can prevent plug rooting.
  • Plugs are heaving out of the ground. This can happen from frost heave in winter or from poor soil contact. Press them back down firmly and add a thin layer of soil around the base.
  • Yellowing leaves. This may indicate a nitrogen deficiency or overwatering. Test soil moisture and adjust watering; if the soil is damp, let it dry a bit. If needed, apply a light nitrogen fertilizer.

Frequently Asked Questions

When is the best time to plant cool season grass plugs? Early fall is ideal because soil temperatures are still warm enough for root growth, but the air is cooler. Early spring also works, but you’ll need to water more as temperatures rise.

How long does it take for plugs to fill in? With proper care, most plugs will spread and fill a 6-inch gap within a few months. Full coverage can take a full growing season, depending on spacing and grass type.

Can I make plugs from my existing lawn? Yes, if your lawn is healthy and you have a similar grass type. Use a plugger to remove small cores and transplant them to the new area. This is a cost-effective way to get plugs.

How often should I water new plugs? For the first week or two, water daily to keep the top inch of soil moist. After that, gradually reduce to every other day, then twice a week, until the grass is established.

Do I need to mow the plugs? Yes, once the plugs reach about a third higher than your normal mowing height, mow them. Keep the mower blade sharp and set high to avoid cutting too much at once.

Will plugs survive winter? Cool season grasses are cold-hardy, so plugs planted in early fall should establish roots before winter and survive. Mulching lightly with straw can help protect them in harsh climates.

Make Cool Season Grass Plugs: A Step-by-Step Guide

Leave a Reply

Your email address will not be published. Required fields are marked *

Scroll to top