Replacing a garden tub faucet is a straightforward DIY project that can refresh your bathroom’s look and fix leaks or drips. Before you start, turn off the water supply to the tub—usually there are shut-off valves under the sink or near the tub. If you don’t see them, turn off the main water valve for the house. This guide assumes you have basic tools and can work carefully with plumbing.
What You’ll Need
- New faucet (make sure it fits your tub’s hole spacing)
- Adjustable wrench
- Basin wrench (for tight spaces)
- Screwdriver (flathead and Phillips)
- Plumber’s tape (Teflon tape)
- Bucket or towel to catch water
- Flashlight
- Plumber’s putty (if required by the new faucet)
- Safety glasses
Step-by-Step
- Turn off the water. Locate the shut-off valves for the tub. Turn them clockwise to close. If there are none, turn off the main water supply to the house. Open the tub faucet to release any remaining water pressure.
- Remove the old faucet handle(s). Look for a small screw on the handle, often hidden under a decorative cap. Pry off the cap with a flathead screwdriver, then remove the screw. Pull the handle off. If it’s stuck, gently wiggle it or use a handle puller.
- Remove the escutcheon (trim plate). The plate that sits against the wall may be held by screws. Remove them and slide the plate off the faucet body.
- Disconnect the supply lines. Use a basin wrench to loosen the nuts connecting the faucet’s supply lines to the shut-off valves. Have a bucket or towel underneath to catch any water. Once loose, pull the supply lines out of the wall or floor.
- Remove the old faucet body. Depending on the model, the faucet body may be held by nuts from underneath or by screws from the top. Use the appropriate wrench or screwdriver to remove it. Carefully pull the faucet out.
- Clean the area. Remove any old plumber’s putty, tape, or debris from the tub surface and the supply lines. Wipe the area dry.
- Prepare the new faucet. Wrap plumber’s tape clockwise around the threads of the new faucet’s supply connections (usually two or three wraps). If the faucet comes with a rubber gasket, you may not need plumber’s putty. If it doesn’t, roll a thin rope of plumber’s putty and press it around the base of the faucet.
- Install the new faucet. Insert the new faucet through the holes in the tub. From underneath, thread the mounting nuts onto the faucet’s shanks. Tighten them with a wrench—but don’t overtighten, as this can crack the tub. If you used putty, wipe away any excess that squeezes out.
- Reconnect the supply lines. Attach the new faucet’s supply lines to the shut-off valves. Hand-tighten first, then give a quarter-turn with a wrench. Be careful not to cross-thread.
- Attach the handles and trim. Slide the escutcheon plate over the faucet body and secure it with screws. Put the handles on and tighten their screws. Replace any decorative caps.
- Turn the water back on. Open the shut-off valves slowly. Check for leaks at the connections. If you see drips, tighten the nuts a bit more.
- Test the faucet. Turn on both hot and cold water. Let it run for a minute, then check under the tub for any leaks. If everything is dry, you’re done.
Common Mistakes
- Forgetting to turn off the water. This can cause a flood. Always double-check that the water is off before disconnecting anything.
- Not using plumber’s tape or putty. This leads to leaks. Use tape on threaded connections and putty on the base if the faucet doesn’t have a gasket.
- Overtightening. Cranking down too hard can strip threads or crack the tub. Tighten until snug, then a little more.
- Cross-threading. When reconnecting supply lines, start threading by hand to ensure they go on straight.
- Buying the wrong size faucet. Measure the distance between the holes in your tub before purchasing. Standard centers are four inches, but some tubs have wider spacing.
Tips
- Take a photo of the old faucet before removing it. This helps you remember how the connections go.
- Use a basin wrench for hard-to-reach nuts—it’s designed for this job.
- Clean the threads of the supply lines with a wire brush before connecting the new faucet.
- Apply plumber’s tape in the direction of the threads (clockwise) so it doesn’t unravel when you screw on the nut.
- If the shut-off valves are old or stiff, consider replacing them while you have access.
- Keep a rag handy to wipe up small spills immediately.
Troubleshooting
- Leak at the base of the faucet. This usually means the putty or gasket isn’t sealing. Remove the faucet, clean off the old putty, and reapply a fresh rope of putty. If the faucet has a rubber gasket, make sure it’s seated properly.
- Leak at the supply line connections. Tighten the nuts a quarter-turn. If it still leaks, turn off the water, disconnect, and reapply plumber’s tape. Check for cracks in the supply lines.
- Water pressure is low. This could be due to a clogged aerator or a partially closed shut-off valve. Remove the aerator and clean it. Ensure the shut-off valves are fully open.
- Handles are loose or won’t stay on. The set screw may not be tightened enough, or the handle may be stripped. Tighten the screw, or if stripped, replace the handle.
- Faucet wobbles. The mounting nuts underneath are loose. Tighten them, but be careful not to overtighten and crack the tub.
- No hot water. Check that the hot water shut-off valve is fully open. If it is, the issue may be with your water heater, not the faucet.
Frequently Asked Questions
- How long does this take? For a beginner, expect to spend a couple of hours. If you’ve done it before, it can take less than an hour.
- Do I need to replace the shut-off valves? Not unless they’re leaking or corroded. If they are, replace them while the water is off.
- Can I use a regular faucet instead of a garden tub faucet? Yes, as long as it fits the hole spacing and has the right supply connections. Many standard bathroom faucets work for garden tubs.
- What if my tub has three holes but the new faucet only uses two? You’ll need a deck plate (escutcheon) to cover the unused hole. Many faucets come with one.
- Why is my new faucet leaking from the spout? This could be a defective cartridge or a loose aerator. Check the aerator first, then consider replacing the cartridge.
- Is it okay to use plumber’s putty on plastic? Yes, but check the faucet instructions. Some manufacturers prefer silicone sealant instead.
How to Replace a Garden Tub Faucet