Planting a tree sapling is an investment in your landscape, but a lawn mower or string trimmer can easily damage or kill it within seconds. Bark damage from mowers and trimmers disrupts the tree’s ability to transport water and nutrients, often leading to slow decline or death. This guide shows you simple, effective ways to shield young trees from mower damage while keeping your lawn neat.
What You’ll Need
- Mulch (wood chips, shredded bark, or compost)
- Tree guard (plastic spiral, mesh tube, or corrugated pipe)
- Stakes (wooden or metal) and a mallet or hammer
- Zip ties, twist ties, or soft twine
- Scissors or utility knife
- Optional: landscape fabric or cardboard
Step-by-Step
- Create a mulch ring around the sapling. Clear grass and weeds in a circle about two to three feet in diameter around the trunk. Lay down a layer of cardboard or landscape fabric to suppress weeds, then spread two to four inches of mulch over it. Keep the mulch a few inches away from the trunk to prevent rot.
- Install a physical tree guard. Wrap a plastic spiral guard around the trunk, starting at the base and spiraling upward. For mesh or corrugated pipe guards, slip them over the top of the sapling and push down to the base. Ensure the guard fits snugly but not so tight that it constricts growth.
- Secure the guard. Use zip ties or soft twine to fasten the guard to the trunk or to a stake. If using a stake, drive it into the ground about six inches from the trunk, then attach the guard to the stake. This prevents the guard from sliding down or spinning.
- Mark the area. Place a brightly colored flag or small decorative fence around the mulch ring. This visually reminds you and anyone else mowing to steer clear of the sapling.
- Mow with care. When mowing, angle the mower so the discharge chute points away from the tree. Use a string trimmer only at a safe distance, or switch to hand clippers for grass near the trunk.
- Check and adjust regularly. Every few weeks, inspect the guard for damage, and loosen any ties that are getting tight as the tree grows. Replenish mulch as it decomposes.
Common Mistakes
- Using a guard that’s too tight. A tight guard can girdle the tree as it grows, cutting off the flow of sap.
- Leaving the guard on too long. Once the trunk is several inches in diameter, remove the guard to avoid trapping moisture and pests.
- Skipping the mulch. Mulch not only suppresses grass but also creates a buffer zone that mowers are less likely to cross.
- Placing the guard too high. The guard should cover the lower trunk, but leaving it too tall can trap moisture against the bark and cause disease.
Tips
- Use a mulch ring that extends at least two feet from the trunk to give the mower a wide berth.
- For extra visibility, use a reflective flag or a brightly colored stake.
- If you have multiple saplings, consider creating a raised bed or border around them to keep mowers away.
- In winter, guards also protect against rodent damage, so leave them on through the cold months.
Troubleshooting
- Guard keeps falling off: Secure it with a stake or use a heavier gauge guard. Make sure the base is buried slightly in the soil.
- Tree bark is already damaged: Clean the wound gently with water, remove any loose bark, and wrap the area with a commercial tree wrap. Do not apply paint or tar, as it can trap moisture. Monitor for signs of disease.
- Grass keeps growing inside the mulch ring: Add a thicker layer of mulch (up to four inches) and consider using a pre-emergent herbicide labeled for use around trees, following label directions.
- Sapling is leaning after mower bump: Straighten it gently and stake it to keep it upright. Water well and monitor for a few weeks.
Frequently Asked Questions
- How long should I keep a guard on a sapling? Keep it on until the trunk is about two inches in diameter, which typically takes two to three years for many trees. Then remove it to prevent girdling.
- Can I use a plastic milk jug as a tree guard? Yes, cut off the bottom and top, then slit the side to wrap around the trunk. It works but may degrade quickly and can trap moisture, so check it often.
- Will a tree die if the mower hits it once? A single nick may not kill it, but repeated damage weakens the tree. If the bark is stripped around the entire trunk, the tree may not survive.
- Should I mulch right up to the trunk? No, leave a few inches of bare soil around the trunk to prevent rot and pest issues.
- What’s the best type of tree guard? A rigid mesh or corrugated pipe guard is durable and allows air flow. Plastic spiral guards are easy to install but may need replacement.
- Can I use a string trimmer near the sapling? Yes, but keep the trimmer head at least a few inches away from the trunk, and use a lower speed to avoid damaging the bark.
How to Protect Tree Saplings from Lawn Mowers