Sliding glass doors are a common entry point for burglars because their standard locks are often weak and easy to bypass. Locking a sliding glass door from the outside isn’t just about using the built-in latch; it’s about reinforcing the entire mechanism so the door can’t be lifted off its track or forced open. This guide covers several methods, from using the existing lock properly to adding simple, affordable security devices. Before you start, inspect your door’s track and rollers for debris or damage, and make sure the door slides smoothly. You’ll need a few basic tools and materials, most of which you may already have at home.
What You’ll Need
- Your sliding door’s original key (if it has a keyed lock)
- A wooden dowel or a metal security bar (cut to fit your track)
- A drill with a small drill bit (for the screw-in lock method)
- A screwdriver (for installing some security devices)
- A measuring tape (to size a dowel or bar)
- A hacksaw (if you need to cut a dowel or bar to length)
- Sandpaper (to smooth cut wood)
- Optional: a commercial sliding door lock, a pin lock, or a patio door security bar
Step-by-Step
- Start with the built-in lock. Most sliding doors have a latch on the inside that hooks into the frame. If your door has a keyed lock (a keyhole on the outside), insert the key and turn it to engage the lock. If not, make sure the interior latch is fully engaged before you go outside.
- Close the door completely. Ensure the door is fully shut and the latch is aligned with the strike plate on the frame. A door that isn’t fully closed won’t lock properly.
- Use a track dowel or bar. Measure the length of the bottom track (the channel the door slides in) when the door is closed. Cut a wooden dowel or a metal bar to that exact length. Place the dowel or bar in the track, snug against the edge of the sliding door. This prevents the door from sliding open even if the latch is broken.
- Install a pin lock (optional). For a more permanent solution, you can install a pin lock. This involves drilling a hole through the top of the door frame and into the door itself. Follow the manufacturer’s instructions, but generally: close the door, mark a spot on the top track, drill a hole through the track and into the door (at an angle), then insert the pin. This locks the door in place and is very effective.
- Add a commercial security bar. Many hardware stores sell adjustable bars that wedge between the door and the frame. These are installed from the inside, but they prevent the door from being opened from the outside. Position the bar so it’s snug against the door and the floor, then tighten it according to the instructions.
- Use a charlie bar (if you have one). A charlie bar is a simple metal bar that sits in the track and flips down to block the door. If your door has one, make sure it’s engaged before you leave.
- Consider a screw-in lock. Some sliding doors have a pre-drilled hole in the track. You can insert a screw or a special lock into this hole to prevent the door from sliding. If you don’t have a pre-drilled hole, you can drill one yourself (at the edge of the door when closed) and insert a screw. This is a low-cost, effective method.
- Test from the outside. After applying any method, go outside and try to slide the door. It should not move at all. If it does, adjust your method.
Common Mistakes
- Relying only on the latch. The standard latch on many sliding doors is flimsy and can be popped open with a screwdriver. Always use an additional method.
- Using a dowel that’s too short. If the dowel or bar doesn’t span the full width of the track, the door can still be slid open a few inches. Measure carefully.
- Forgetting to lock the door before leaving. It sounds obvious, but many people forget to engage the lock before going out. Make it a habit.
- Drilling holes without checking for obstacles. Before drilling, make sure you aren’t drilling into wiring or pipes. Use a stud finder if you’re unsure.
- Not maintaining the track. Dirt and debris can prevent the door from closing fully, which means the lock won’t engage properly. Keep the track clean.
Tips
- Use a wooden dowel with a snug fit. A dowel that fits tightly in the track is harder to dislodge. Sand it lightly if it’s too tight.
- Combine methods. Use the built-in lock plus a dowel or bar for maximum security.
- Install a security camera or motion light. These act as deterrents and can alert you to attempted break-ins.
- Keep the key in a safe place. If you have a keyed lock, don’t hide the key under the doormat. Give it to a trusted neighbor or use a secure lockbox.
- Check your lock regularly. Over time, locks can wear out. Test your lock every few months and lubricate the track with a silicone spray.
Troubleshooting
- The door won’t close fully. This is often due to debris in the track or misaligned rollers. Clean the track and adjust the rollers (usually with a screwdriver) so the door sits evenly.
- The key is stuck or won’t turn. Spray a dry lubricant (like graphite) into the keyhole and gently wiggle the key. If it still won’t turn, the lock may be damaged and need replacement.
- The dowel keeps falling out. Make sure the dowel is cut to the exact length and is thick enough to sit snugly in the track. You can also add a small piece of adhesive felt to the ends to increase friction.
- The security bar won’t stay in place. Check that the bar is adjusted correctly and that the floor and door frame are clean. Some bars need a rubber pad to grip better.
- The door is still loose even with a lock. If the door can be lifted off its track, you may need to install anti-lift devices (screws in the top track) to prevent this. This is a more advanced fix; consider hiring a professional.
Frequently Asked Questions
Can I lock a sliding glass door from the outside without a key?
Yes, you can use a track dowel, a security bar, or a pin lock. These methods don’t require a key and are often more secure than the built-in lock.
Is a wooden dowel really effective?
Yes, a wooden dowel placed snugly in the track is a classic, effective deterrent. It prevents the door from sliding open, and it’s inexpensive. However, it doesn’t prevent the door from being lifted off the track, so combine it with other measures.
How do I know what size dowel to buy?
Measure the width of the track channel (the groove the door slides in). A dowel that’s about 1/2 inch to 3/4 inch in diameter usually works. Cut it to the length of the track when the door is closed.
Should I drill a hole in the track?
Drilling a small hole in the track and inserting a screw is a common DIY security method. It’s effective, but it does alter the door. If you’re not comfortable drilling, use a dowel or a commercial lock instead.
What’s the best commercial lock for a sliding door?
There are several good options, including pin locks, keyed locks, and security bars. Look for one that is made of sturdy metal and is designed specifically for sliding doors. Read reviews and choose one that fits your door’s track.
Can a sliding door be locked from the outside if the inside lock is broken?
Yes, you can still secure it with a track dowel, a security bar, or a pin lock. These methods work independently of the built-in lock. If the built-in lock is broken, it’s a good idea to replace it or install a secondary lock.