Filling a hole in plasterboard (drywall) is a straightforward repair that restores the wall so you can paint over it and forget the damage ever happened. Small holes from picture hooks or doorknobs take only a few minutes with a little filler. Larger holes, up to about the size of your fist, need a patch piece of plasterboard and some mesh tape. This guide walks you through both, starting with the simple method and then the stronger repair for bigger gaps. Before you begin, make sure the edges of the hole are loose-free; if the paper facing is peeling or the board crumbles, cut back to solid material first.
What You’ll Need
- All-purpose joint compound (drywall mud) or a ready-mixed filler for small holes
- A putty knife or filling knife (a few inches wide)
- Fine sandpaper or a sanding sponge
- A dust mask and a damp cloth
- For larger holes: a piece of plasterboard scrap, a utility knife, a drywall saw or keyhole saw, mesh tape, and a screwdriver or drill
- Primer and paint to finish
Step-by-Step
- Prepare the hole. Remove any loose plaster, dust, or crumbly edges. If the paper facing around the hole is torn or lifted, cut it away with a utility knife so you have a clean, solid edge. Wipe the area with a damp cloth to settle dust.
- Fill small holes (up to about the size of a coin). Scoop a small amount of joint compound onto your putty knife and press it firmly into the hole, overfilling slightly. Drag the knife across the hole to level it, then let it dry completely. Apply a second thin coat if needed to bring it flush with the wall.
- Patch medium holes (up to a few inches across). Cut a piece of mesh tape slightly larger than the hole. Stick it over the hole, then spread a thin layer of joint compound over the tape, pressing it into the mesh. Feather the edges out a few inches beyond the tape. Let dry, then apply a second coat that is wider still, feathering the edges to blend with the wall.
- Patch large holes (bigger than a few inches). Use a drywall saw to cut the hole into a neat square or rectangle. Cut a scrap piece of plasterboard to fit that opening, leaving about a half-inch of paper on the front of the scrap around all edges (score the paper, snap the board, then peel the paper). Apply a thin layer of joint compound around the inside edges of the hole, press the scrap in so its paper overlaps the wall, and smooth it down. Let dry, then tape over the seams with mesh tape and apply joint compound as in step three.
- Sand smooth. Once the final coat is dry, sand the area with fine sandpaper or a sanding sponge. Work in a circular motion and check with your hand—it should feel perfectly flat. Wipe away the dust with a damp cloth.
- Prime and paint. Apply a coat of primer over the repaired area to seal the compound and prevent flashing (a dull patch that shows through paint). Let it dry, then paint to match the wall. Two coats of paint usually give the best blend.
Common Mistakes
- Skipping the primer—this makes the patch visible even after painting.
- Using too much filler at once, which shrinks and cracks as it dries. Build up in thin layers.
- Not feathering the edges—leaving a raised lip that casts a shadow.
- Sandpapering dry compound without a mask, breathing in fine dust.
- Forgetting to cut away loose paper, which causes the filler to bubble or peel.
Tips
- For very small holes, a tube of ready-mixed filler you squeeze directly into the hole works well and needs no mixing.
- Hold the putty knife at a slight angle and pull it across in one smooth motion for a cleaner finish.
- Use a damp sponge instead of sandpaper for the final smoothing—it creates less dust and leaves a fine finish.
- If the hole is near a corner or edge, use a corner trowel or a smaller knife to get into the angle.
- Let each coat dry fully before adding the next; rushing leads to shrinkage cracks.
Troubleshooting
The filler keeps cracking. This usually means the coat was too thick. Let it dry, scrape out the crack, and apply a thinner coat. If the hole is deep, fill it in stages rather than all at once.
The patch is still visible after painting. You likely skipped primer or didn’t feather enough. Sand the area lightly, apply a wider skim coat of compound, sand again, then prime and repaint.
The plasterboard patch piece won’t stay flat. The opening may be slightly too small, forcing the piece to bow. Remove it, trim the opening a little, and press the piece in again. For stubborn cases, a few small screws through the patch into the studs (if any are behind) will hold it while the compound dries.
The mesh tape shows through. You didn’t cover it with enough compound. Apply another thin coat over the tape, feathering well beyond its edges, and sand smooth.
Dust keeps sticking to the wet filler. Wipe the area with a tack cloth or damp cloth right before applying the next coat, and work in a clean room.
Frequently Asked Questions
Can I fill a hole without a patch piece? For holes smaller than a few inches, yes—just use mesh tape and joint compound. For larger holes, the tape alone won’t be strong enough, and you need a backing piece or a plasterboard patch to support the compound.
How long does the filler take to dry? Most joint compounds dry in a few hours, but it depends on thickness, humidity, and airflow. Check the manufacturer’s label; when it’s fully dry, it turns a uniform color and feels hard.
Do I need to use mesh tape for every hole? No. For tiny holes, filler alone is fine. Tape is only needed when the hole is big enough that the filler might sag or crack without reinforcement.
What if the hole goes all the way through to the other side? You’ll need a backing piece behind the hole. You can use a piece of string tied to a small wood block, or a purpose-made drywall repair clip, to hold the patch in place while the compound sets.
Can I paint directly over the filler without primer? You can, but the paint may dry unevenly and the patch will look dull. Primer seals the porous compound and gives a uniform surface, so it’s worth the extra step.
How do I match the texture of my wall? If your wall has a texture like orange peel or knockdown, apply a thin layer of compound and stipple it with a sponge or brush to mimic the pattern before it dries. Practice on a scrap piece first.