Replacement windows often use a balance system with a coiled spring to hold the sash open at any height. Over time, the spring can lose tension, making the window sag or not stay up. Adjusting the tension restores the counterbalance so the window moves smoothly and stays where you put it. Before you start, identify your window type: most modern vinyl and aluminum windows use a spiral balance or a block-and-tackle balance. You’ll need to know which one you have, as the adjustment method differs. Always work with the sash closed or removed, and never force a part that seems stuck—it may be a different system than you think.
What You’ll Need
- Screwdriver (flathead or Phillips, depending on your window)
- Adjustable pliers (for spiral balances)
- Allen wrench (hex key) if your balance has a set screw
- Clean cloth and mild lubricant (silicone spray, not oil-based)
- Safety glasses (optional, but recommended)
Step-by-Step
- Identify the balance type. Open the window and look at the top of the sash. If you see a metal tube with a spiral rod inside, it’s a spiral balance. If you see a cord or chain running over a pulley, it’s a block-and-tackle balance. Most tilt-in vinyl windows use spiral balances; older wood windows often use block-and-tackle.
- Close the window and remove the sash. Tilt the sash inward (if it’s a tilt-in type) by pulling the bottom out, then lift the sash out of the frame. For double-hung windows, you may need to release the tilt latches first. If your window doesn’t tilt, you may need to remove the stop molding—use a pry bar carefully, but note that this is more complex and may require professional help.
- Locate the adjustment point. For spiral balances, look at the top of the balance tube. There is usually a small gear or a flat area that can be turned with a screwdriver. For block-and-tackle balances, the adjustment is often a small screw or a clip on the side of the balance, near the top.
- Adjust spiral balances. Insert a flathead screwdriver into the gear slot at the top of the balance. Turn the screwdriver clockwise to increase tension (to make the window stay up better) or counterclockwise to decrease tension (if the window is too hard to close). Turn in small increments—half a turn at a time—and test after each turn.
- Adjust block-and-tackle balances. If your balance has a small screw, turn it clockwise to tighten the spring. If it has a clip, you may need to unhook it and move it to a different hole on the tensioning arm. This varies by manufacturer, so consult your window’s manual if you have it.
- Reinstall the sash. Lift the sash back into the frame, making sure the balance shoes (the metal parts that slide in the tracks) engage correctly. Tilt the top into the frame, then push the bottom in and close the window.
- Test the tension. Open the window halfway and let go. It should stay in place without drifting up or down. If it falls, increase tension. If it’s hard to move or won’t stay closed, decrease tension. Repeat the adjustment until it feels smooth.
- Lubricate the tracks. After adjusting, spray a small amount of silicone lubricant on the tracks and the balance shoes. Wipe off any excess with a cloth. This helps the window glide smoothly and reduces wear on the balance.
Common Mistakes
- Over-tightening. Turning the tension too far can break the spring or strip the gear. Always make small adjustments and test frequently.
- Adjusting the wrong balance. On a double-hung window, each sash has its own balance. Adjusting the top sash when the problem is the bottom sash will not fix the issue.
- Forcing a stuck balance. If the balance doesn’t turn, it may be seized or broken. Forcing it can damage the window frame.
- Using oil-based lubricants. Oil attracts dust and can gum up the tracks over time. Stick to silicone-based sprays.
- Ignoring the tilt latches. If you don’t release the tilt latches before removing the sash, you can break them.
Tips
- Take a photo of the balance before you adjust it, so you can remember the original position.
- If you have multiple windows, adjust them one at a time and label each sash if you remove several.
- Test the window at different heights—the tension may be correct in the middle but not at the top or bottom.
- Clean the tracks before adjusting, as dirt can cause the window to stick and mimic a tension problem.
- If the balance is broken (spring snapped or cord frayed), adjustment won’t fix it. You’ll need to replace the balance unit.
Troubleshooting
Window still falls after full adjustment. The spring may be worn out and need replacement. Check the balance for signs of corrosion or damage. If it’s a spiral balance, you can often replace just the balance unit—look for the brand and model on the tube.
Window is too hard to close. You’ve likely over-tightened. Decrease tension by turning the screwdriver the other way. If the window was already hard before you started, the tracks may be dirty or the sash may be swollen from humidity.
Window doesn’t stay at the same height on both sides. The two balances (one on each side) may have different tensions. Adjust the one that is weaker (the side that slips) to match the other.
Balance won’t turn. The gear may be stripped or the spring may be seized. Try spraying a bit of penetrating oil on the gear and waiting a few minutes. If it still won’t turn, the balance is likely broken and needs replacement.
Sash won’t come out. Make sure you’ve released the tilt latches completely. If the window has a fixed sash (not tilt-in), you may need to remove the stop molding—this is more involved and may require a putty knife to avoid damaging the wood.
Frequently Asked Questions
How often should I adjust window tension?
There’s no set schedule. Adjust only when you notice the window won’t stay up or is difficult to move. Regular cleaning and lubrication can extend the life of the balance.
Can I adjust any window tension myself?
Most modern windows with accessible balances are DIY-friendly. However, if your window is old, has a non-tilt sash, or the balance is hidden behind a fixed stop, it’s safer to call a professional to avoid damaging the frame.
What if I don’t know the brand of my window?
Look for a label on the glass or the frame. If there’s none, the balance may still have a brand name stamped on it. If you can’t identify it, take a photo to a hardware store or window repair specialist for help.
Will adjusting tension fix a window that’s stuck?
No. A stuck window is usually due to dirt, paint, or a misaligned sash. Clean the tracks and check for obstructions first. If it’s still stuck, the balance may be broken and need replacement.
Is it normal for the tension to feel different in winter?
Yes. Temperature changes can affect the spring and the window materials. If the window sags only in cold weather, a slight increase in tension may help, but don’t over-tighten.
Can I adjust tension without removing the sash?
Some balances have an external adjustment screw accessible from the side of the window frame. If you don’t see one, you’ll need to remove the sash to reach the balance top.