DIY Firewood Storage with Cinder Blocks

Building a firewood rack from cinder blocks and lumber is one of the fastest, cheapest, and most durable ways to keep your firewood dry and off the ground. The open design allows air to circulate around the logs, which prevents rot and keeps pests from nesting in the stack. This project takes about an hour, requires no special skills, and uses materials you can find at any hardware store or reuse from a previous project.

What You’ll Need

  • Concrete cinder blocks (also called CMUs) – you will need enough to make two columns, each three to four blocks high. A typical rack uses six to eight blocks.
  • Pressure-treated lumber – two long boards (about 4×4 inches or 2×6 inches) to serve as the base rails, and two shorter boards for the end stops. Length depends on how much wood you want to store.
  • A level (a small bubble level works fine).
  • A tape measure.
  • A saw (circular saw or handsaw) to cut the lumber to length.
  • A shovel or trowel to level the ground.
  • Optional: landscape fabric or gravel to place under the rack.
  • Optional: wood preservative or sealer for the lumber.

Step-by-Step

  1. Choose a location. Pick a spot that is at least a couple of feet away from your house or any wooden structure. This keeps termites and moisture from transferring to your siding. Make sure the ground is fairly level and well-drained – avoid low spots where water pools.
  2. Clear and level the ground. Remove grass, weeds, and debris. Use a shovel to dig down a few inches if needed to create a flat surface. If you want extra protection, lay down landscape fabric and spread a layer of gravel over the area. This prevents weeds and improves drainage.
  3. Cut your lumber. Measure the length you want for the rack. A good size is about four feet long, which holds roughly a quarter cord of wood. Cut two long boards to this length for the rails. Cut two shorter boards (about one foot long) for the end stops. If you are using 4x4s, you can skip the end stops and just let the rails extend past the blocks.
  4. Lay the first course of blocks. Place two cinder blocks flat on the ground, parallel to each other, spaced about three feet apart. These will be the base of your two columns. Use the level to check that they are even with each other. Adjust by adding or removing soil under them.
  5. Stack the columns. Add another block on top of each base block, making sure the holes line up vertically. Continue until each column is three or four blocks high. The taller the column, the more wood you can stack, but keep it stable – four blocks high is the practical maximum for a freestanding rack.
  6. Set the rails. Place one long board across the top of each column, resting in the holes or on the flat surface of the top block. If the blocks have holes facing up, the board will sit securely in the groove. Make sure the boards are parallel and level.
  7. Add the end stops (optional). If you are using 2×6 rails, place the short boards vertically at each end, between the rails, to keep logs from rolling off. You can also just stack the wood tightly and rely on the end blocks to hold it in place.
  8. Start stacking firewood. Place the first row of logs on the rails, bark side down, with the cut ends facing out. Stack in alternating directions (some logs lengthwise, some crosswise) to create a stable interlocking pile. Leave a small gap between logs for air circulation.
  9. Build up the stack. Continue stacking rows, making sure the pile leans slightly backward against the columns if you want extra stability. Do not stack higher than about four feet – taller piles become unstable and dangerous to pull from.
  10. Cover the top. Use a tarp, metal roof panel, or piece of plywood to cover only the top of the stack. Leave the sides open so air can flow. Weigh the cover down with a brick or block so it does not blow away.

Common Mistakes

  • Using untreated lumber directly on the ground. Even if the blocks keep the wood off the soil, the rails themselves will rot if they touch damp earth. Always use pressure-treated lumber or place a plastic barrier between the rails and the blocks.
  • Stacking wood too high. A tall pile looks impressive but is a tipping hazard. When you pull a log from the bottom, the whole thing can collapse. Keep the stack under four feet.
  • Covering the sides. A tarp wrapped around the entire rack traps moisture and causes mold. The sides must stay open for airflow. Only the top needs protection from rain and snow.
  • Placing the rack against a wall. This blocks airflow on one side and can transfer moisture to your house. Always leave a gap of at least a few inches between the rack and any wall.
  • Not leveling the ground. If the blocks are uneven, the rails will twist and the stack will lean. Take the time to level the base properly.

Tips

  • Season your wood before burning. Freshly cut wood needs at least six months to a year to dry. The cinder block rack is perfect for this because the airflow speeds up the drying process.
  • Stack the wood bark side up on the top row to shed water, but bark side down for the lower rows to keep moisture from being trapped.
  • If you have a lot of wood, build two racks side by side with a gap between them. This lets you access both stacks easily and keeps the overall height lower.
  • Use the holes in the cinder blocks to your advantage. You can insert short pieces of rebar or PVC pipe vertically to create additional support for the rails.
  • Check the rack periodically, especially after heavy rain. If the blocks start to sink or lean, re-level them before the stack gets too heavy.
  • For a more permanent solution, you can mortar the blocks together, but this makes it harder to move the rack later.

Troubleshooting

  • The rack wobbles. This usually means the ground is not level. Remove the blocks and re-level the soil. You can also place a single flat paver stone under each base block for a more stable footing.
  • Logs keep falling off the ends. Add the end stops or place a couple of logs crosswise at each end to act as a bumper. You can also stack the end logs slightly angled inward.
  • Mold or mildew on the wood. This means the wood is not getting enough airflow. Check that the sides are not covered and that the stack is not too tight. If the wood is already wet, pull the pile apart and let it dry before restacking.
  • Ants or termites in the pile. This is common when wood sits directly on the ground. Since your rack is off the ground, this should be minimal. If you see pests, remove the affected logs and inspect the ground for a nest. Keep the area around the rack clear of debris.
  • The rails sag in the middle. This happens when the span between the two columns is too long. Add a third column of blocks in the middle to support the rails, or use thicker lumber like a 4×6.
  • The whole rack tips forward. The stack is likely top-heavy. Reduce the height and make sure the base blocks are buried slightly into the ground for stability. You can also angle the columns slightly backward.

Frequently Asked Questions

  • How long will the cinder blocks last? Cinder blocks are extremely durable and can last for decades outdoors. They are not affected by moisture or insects, so the main thing that will wear out is the lumber, which you can replace easily.
  • Can I use regular lumber instead of pressure-treated? You can, but it will rot much faster when exposed to moisture. Pressure-treated lumber is worth the extra cost because it will last several times longer. If you use regular lumber, seal it with a wood preservative and keep it off the ground.
  • How much firewood can this rack hold? A four-foot-long rack with three-foot-high columns holds roughly a quarter cord of wood when stacked tightly. A quarter cord is about the amount you would use for occasional evening fires over a season. You can build a longer rack to hold more.
  • Do I need to cover the firewood? Yes, covering the top is essential to keep rain and snow off. But do not cover the sides – the wood needs air to dry. A simple tarp or sheet of metal roofing works well.
  • Can I build this on a concrete patio or deck? Yes, but make sure the surface is level. On a deck, you might want to place a rubber mat or small piece of plywood under each block to protect the deck surface from scratches. Also, check that the deck can support the weight of the wood.
  • Is it safe to store firewood against my house? It is not recommended. Firewood attracts termites and other pests that can migrate into your home. Keep the rack at least a couple of feet away from any structure, and never stack wood directly against siding.
DIY Firewood Storage with Cinder Blocks

Leave a Reply

Your email address will not be published. Required fields are marked *

Scroll to top